Gravure Ink Color Testing Machine for Water-Based Inks

Introduction:
CP150 Gravure ink proofer can print gravure inks quickly under the experiment condition,and the method is closed to the actual printing. The gravure ink proofer is used to laboratory production,ink printability test and ink product research.It adopts flat intaglio printing work directly for quick proofing in a varity of flexible substrates(such as plastic film,paper,etc.).It is so easy to operate.The machine is supplied with a special version of the gravure proofing.
 
2. TECHNICAL SPECIFICATION OF CP150 GRAVURE INK PROOFER:
1. Electrical Power Source:220V
2. Frequency: 50HZ
3. Sample size: 120*240mm
4. Weight: 26kg
5. Motor Power: 120w
6. Roll/Hardness: 76*130mm/shoreA55
7. Printing Speed: 20/30/40/45m/min
8. Printing Length: 95*149mm
9. Dimension: 500*400*350mm
THE OPERATION SUMMARY:
The proofer should be put on the solid flat place.
Install Gravure Proofing Edition: put the edge which is printed with specification on the distal, put the edge without word to fasten the proofing edition mouth , compression screw.
Loosen the clamping lever, lift proofing moving frame. Attach the squeegee to the proofing moving frame, after fastening screws about positioning pins. The beater backward is about 45 degrees, suitable compression screw fastening beater.
Push back the proofing moving frame in the end .Adjust the scraper adjuster and roller adjuster , make sure the squeegee and roller could not touch the proofing edition mount.
Lower the proofing moving frame,lock the clamping lever,turn down adjuster(before adjustment loosen the lock ring at the bottom,adjust and then lock),so between close rubber roller and proofing edition has close suitable pressure(pressing proof can not be easily withdraw).Generally will increase by about 1 to 2 turns screw micrometer scale at the beginning of the rubber roller and pareller proofing edition after a clockwise touch,after India test case,as the leveling to do the approprite adjustments.
Adjustment downward blade adjuster (before adjustment loosen the lock ring at the bottom,adjust and then lock).So squeegee blade and proofing between version has a suitable pressure (non-concave like portion can scrape the remainder of the ink can be).Generally will increase by about 1 to 2 turns screw micrometer scale at the beginning of the doctor blade and parallel proofign edition after a clockwise touch, after the trial, as the printing squeegee circumstances do appropriate adjustments.
Loosen tight grip level,confirm proofing moving frame has back foot,Proofing/Manual/Reset Knob in the manual position(center position).Power,turn on the power switch.First select 1 at the speed (20m/min),the Sampling/Manual/Reset switch to the proof file,confirm proofing moving frame slides smoothly.Select the appropriate sampling rate(usually the beginning choose 3 position(40m/min).such as the flow level after the test print is not satisfactory appropriate to reduce the sampling rate can be reset.
Proofing operation: The flexible substrate proofs suitable width and length(plastic film.cardboard,recommended 120*240mm size) with a transparent adhesive tape to glue roll (pasted along the direction of the incoming end of the can). Paste the terminal to the appropriate starting position (roughly in the vicinity of the beater), lock the clamping lever, the amount of ink placed on the blade near proofing Edition (concave-like at the beginning, close to the concave-like width not exceeding appropriate). The "Proof / Manual / Reset" switch to the "proof" position, proofing move forward quickly with the selected frame rate from the complete proofing Dodo.
Loosen the clamp handle, remove the proofs. Lift proofing moving frame and select "Reset" position to retract in the end (reset speed is factory preset good). Use a soft cloth with solvent ink residue scraper quickly, proofing version and the rubber roller cleaned in preparation for the next sampling operation. In the scrubbing process can be "sampling / Manual / Reset" knob to "manual" position (center position), so you can move back and forth freely moving frame proofing, easy to scrub operation. After completion of the reset proofing scrub moving frame.
Observe proofs of printing effects, depending on the case proofing inks or equipment can make the appropriate adjustments.
 
4.NOTE:
1. This machine is used for chemical raw materials testing process, the user should press the relevant safety before use. Provisions to establish appropriate safety and health protection measures and determine the rules and regulations. And chemical raw material exposure related security issues should be established by the user, it does not belong to illustrate the scope of the specification. The protective paper proofing edition, please take away 2. initial use.
2. When load moves forward proofing moving frame, do not select "4" position (45 / m) ProofingSpeed
3. Proofing version timely installation of the slide rail portion of the audience for lubrication.
4.Each time a sampling operation, and must be thoroughly cleaned of residual ink on proofing version, to avoid making Into a "paste board." Proofing samples before confirmation concave portion without any residue.
5.Proofing version, squeegee and rubber rollers proofing effect plays an important role, use should be avoided bump, scratch, and should be timely to do cleaning and maintenance work.
6. For use in proofing manually move mobile frame, set "sampling / Manual / Reset" knob to set in. If you select "proofing" file, proofing moving frame rate will be selected quickly move forward. If you select "Reset" file, proofing moving frame at a preset speed back back. Fallback speed is factory preset, usually without adjustment (ailable through the small opening at the bottom of the unit to be adjusted).
7. The company will market customer's requirement, keep continuous improvement and product development. The specification subject to change without notice.
 
ATTACHMENT SELECTOR:
CP150 SPECIAL INK PRINTING GRAVURE PROOFING
CP150 gravure proofing-specific ink is carved through fine processing, it is designed for gravure printing ink proofer, flexographic printing ink used to provide matching proofer.
              
       VERSION D      VERSION C     VERSION B    VERSION A
 
 
 
Technical specification:Note: * Number customized version.